.62 Cal Flintlock Hunter

CowboyCS

Well-known member
For about 5 years now I've wanted to build this rifle, I've actually been working on it a little here and a little there for almost 3 years now. The Mechanic's Car, the Shoemaker's kids and the Gunsmith's gun all seem to be the same story, you get so busy building for customers you can never find the time to build anything for your self. So I slowly put an hour or two at a time in on this thing for nearly 3 years to finally get the Flintlock hunting rifle I have envisioned for a while now.

I know when people look at this they are going to say how it isn't historically or period correct but that is actually the point. I have owned several flintlock rifles and I think they are fine guns for rendezvous or re-enacting but they have never been my cup of tea when it comes to hunting. They are long barreled, full stocked, heavy and just not my taste in hunting rifles. The few Halfstock Flintlock rifles on the market didn't interest me either, CVA, TC, Lyman all make a half stock flintlock but they are all patterned after a variation of the plains rifle, they all have untapered barrels, they all have underribs or at the very least pipes and a ramrod hanging under the barrel and none of them comes in a caliber bigger than .58. And they are mostly pretty heavy.

I wanted a rifle that feels, weighs, handles and generally looks like one of my modern cartridge rifles but is still legal to hunt anywhere in the U.S. during muzzleloading season.

Down to the details:
.62 Caliber Colerain Barrel Slow twist for Patched Roundball. 32" long tapered.
R.E. Davis Lock
Pachmyer Decelerator Recoil Pad, I like steel buttplates but I plan to be shooting this for many years to come and I like recoil less and less these days.
The Trigger, Triggerguard and Grip Cap I made myself.
The stock is American Black Walnut with an ebony forearm cap.
The sights were just extras I had laying around from TOTW...single leaf rear and a silver blade front.
The stock is oil finished and waxed to give a nice matte(low sheen).
The metal is rust blued and also done to a matte finish.
I don't like my hunting rifle to give off a lot of reflection.
To keep the weight down I didn't add an underib or pipes and ramrod instead I made a multi-piece ramrod for my possibles bag.
Weight is 6 pounds 10 Ounces.

The Rifle:






The Target:

6" x 6" square the black circle is approx 2" diameter
100 yards, offhand, un-supported
120grs FFG Goex
4Fg pan
.600 diameter 97% lead - 3% Antimony (325ish grains, I haven't weighed one yet to see exactly)
.018" Pillowticking Veg Lube

The one flyer was totally my fault I had a very slight hang fire and I didn't hold through like I should have. I think with more load development I can probably tighten the group up a bit more but since Muzzleloader season starts here in about 3 weeks I may not have time to get back out and do the load work so for now I am satisfied enough to take it hunting white-tail.

Thanks for looking,

Colin
 

inchr48

Moderator
Moderator
In awe as always. I'd say you are ready for the season to begin. Hope a Booner steps out in front of you.
 

BelchFire

I speak fluent Vise-Grip
Admin
That's one heck-uv-a cavity on the end of that thing! You been breeding you deer with your cows? Beautiful work, as usual! :thumbs up:
 

CowboyCS

Well-known member
Thanks for the compliments guys.

Belchfire, the deer aren't that big here but I might want to hunt elk or moose with it in the future and the 62 is a good all around caliber for North America.

Colin
 

FTTPOW

Moderator
Moderator
Colin, I've seen your work and hefted your guns while at Friendship a few years back. Your quality is outstanding. Something I noticed or lack thereof. How are you holding the lock in place? I can't see any screw heads on the back side.
 

CowboyCS

Well-known member
Thanks for the compliments.

FTTPOW,
If you look closely at the 3rd picture(the close up lock side), you can see a screw head between the hammer and pan/skirt(it's countersunk flush). That screw is threaded into the tang/breechplug this eliminated the need to drill clear through the stock and inlet anything on the offside.

Colin
 
Last edited:


Top Bottom